ozdevil Posted November 10, 2023 Share Posted November 10, 2023 (edited) Well its been along time between drinks in this house hold No Pictures you have all seen wort in a container before so not much different here Made up a Hop Nation XPA from Grain and Grap usinging US-05 i was going to use Bluestone San Diego -bsy - A010 ale yeast but couldnt be bothered driving to keilor in 30°c heat just for 1 sachet of yeast but i am eager to try the bluestone yeast have heard some good things made it up to 20 litres so it wont be as high alchol % as the real hop nation xpa but it still will be good starting gravity was 1.042 if i brewed to 15l it would have been 1.051 happily fermenting under pressure now and i spose i better get my 20litre bottle ready to fill in the next week or so finally good to see a brew in the fermenting fridge Edited November 10, 2023 by ozdevil 8 Link to comment Share on other sites More sharing options...
DavidM Posted November 10, 2023 Share Posted November 10, 2023 Irish Red Ale Trying another variety in this style, see how it goes. Uped the Malt by 500g's and the roasted barley to 100g's. Made it up to 23l. The recipe page said to "add the grain to 2l of water at the boil, remove from the heat, and Steep for 60 min." I've done all my steeps with a target temp of 65 degrees. Which is what I did with this one. Can anyone see a reason to steep the grain from the boil (as the recipe said)? (Remember this is an Extract Brew!) 2 Link to comment Share on other sites More sharing options...
Back Brewing Posted November 10, 2023 Share Posted November 10, 2023 @Pale Man how did you go putting down the fwk what pouring method did you use? Link to comment Share on other sites More sharing options...
Pale Man Posted November 10, 2023 Share Posted November 10, 2023 42 minutes ago, Back Brewing said: @Pale Man how did you go putting down the fwk what pouring method did you use? Hey fella I opened screw top lid, pointed the ring pull at my fermenter and yanked it out. To be truthful i didnt spill much, but the bit I did, went over the screw top of the fermenter lid area. Which if not cleaned up before pitching yeast could introduce any nastys. You dont want sticky wort above the fermenting wort. These FWK bladders are a nuisance all in the name of saving money. Havent got a reply yet from All In Brewing. 3 Link to comment Share on other sites More sharing options...
Kegory Posted November 10, 2023 Share Posted November 10, 2023 4 hours ago, DavidM said: Irish Red Ale Trying another variety in this style, see how it goes. Uped the Malt by 500g's and the roasted barley to 100g's. Made it up to 23l. The recipe page said to "add the grain to 2l of water at the boil, remove from the heat, and Steep for 60 min." I've done all my steeps with a target temp of 65 degrees. Which is what I did with this one. Can anyone see a reason to steep the grain from the boil (as the recipe said)? (Remember this is an Extract Brew!) I recently made one of those. It seems to be an old recipe. I asked for some guidance on it in the recipe section. You should be able to find the thread relatively easily, it was only last month. I steeped for 30 minutes between 60 & 70. I think I'm due for a taste test this weekend. Keep an eye on the What Are You Drinking 2023 thread. 1 Link to comment Share on other sites More sharing options...
Uhtred Of Beddanburg Posted November 10, 2023 Share Posted November 10, 2023 (edited) @Pale Man I have done it a few ways one Is holding it facing the fermenter squeezing some of it between my legs when pull the tab out. The other is pulling the tab out while it's upright then holding the opening and grabbing one corner and tip it. I wouldn't consider myself a strong person and I'm short. Both I find easy and never spill a drop. Yes its heavy and awkward for 5 or 10 seconds but it empties so fast it's not a problem. Sorry you find it hard I hope other suggestions or mine can help you. As cost saving for the company also means the consumer. I'm also sure they would do cubes if they got them back for re use. Grain and grape in yaraville ask locals to return cubes where possible. Edited November 10, 2023 by Uhtred Of Beddanburg 2 Link to comment Share on other sites More sharing options...
Classic Brewing Co Posted November 10, 2023 Share Posted November 10, 2023 2 hours ago, Pale Man said: Hey fella I opened screw top lid, pointed the ring pull at my fermenter and yanked it out. To be truthful i didnt spill much, but the bit I did, went over the screw top of the fermenter lid area. Which if not cleaned up before pitching yeast could introduce any nastys. You dont want sticky wort above the fermenting wort. These FWK bladders are a nuisance all in the name of saving money. Havent got a reply yet from All In Brewing. Try my method, I don't spill a drop. 1 Link to comment Share on other sites More sharing options...
Pale Man Posted November 10, 2023 Share Posted November 10, 2023 14 hours ago, Classic Brewing Co said: Try my method, I don't spill a drop. I still dont get how you do it. Link to comment Share on other sites More sharing options...
Classic Brewing Co Posted November 10, 2023 Share Posted November 10, 2023 (edited) 25 minutes ago, Pale Man said: I still dont get how you do it. OK, Mr Paleman, a milk crate built up to just under the height of the bench placed as close as possible to where the FWK box will be placed with the tap/nozzle facing the front, cut around the cardboard to expose it, I don't handle the bladder at all. I haven't got the box so just imagine the baby FV is the FWK, it just simply pours in to the FV, I place a plank of wood at the back of the box to make it easier & when the box is easier to handle just lift it up over the FV, then if you want you can remove the bladder & get every bit of the sucker in to the FV, like I said I don't spill any. The video is the same principle. Tip always pour a cold beer from the tap first to ensure a smooth delivery. Cheers. 20230412_115941.mp4 Edited November 10, 2023 by Classic Brewing Co 1 Link to comment Share on other sites More sharing options...
Pale Man Posted November 10, 2023 Share Posted November 10, 2023 3 minutes ago, Classic Brewing Co said: OK, Mr Paleman, a milk crate built up to just under the height of the bench placed as close as possible to where the FWK box will be placed with the tap/nozzle facing the front, cut around the cardboard to expose it, I don't handle the bladder at all. I haven't got the box so just imagine the baby FV is the FWK, it just simply pours in to the FV, I place a plank of wood at the back of the box to make it easier & when the box is easier to handle just lift it up over the FV, then if you want you can remove the bladder & get every bit of the sucker in to the FV, like I said I don't spill any. The video is the same principle. Tip always pour a cold beer from the tap first to ensure a smooth delivery. Cheers. 20230412_115941.mp4 15.8 MB · 0 downloads Its not how you set it up that I dont get. Its the hole in the carboard to sit the spout in. You cut your own hole? Do you pull the ring tab while its sitting in the box or before and put the lid back on? Then just unscrew the lid while its set up. 1 Link to comment Share on other sites More sharing options...
Classic Brewing Co Posted November 11, 2023 Share Posted November 11, 2023 2 minutes ago, Pale Man said: Its not how you set it up that I dont get. Its the hole in the carboard to sit the spout in. You cut your own hole? Do you pull the ring tab while its sitting in the box or before and put the lid back on? Then just unscrew the lid while its set up. You cut your own hole? Yes, I open the end of the box where the spout is enough to expose it to make pouring easier. The rest of the box is intact. 2 Link to comment Share on other sites More sharing options...
Kegory Posted November 11, 2023 Share Posted November 11, 2023 54 minutes ago, Pale Man said: Its not how you set it up that I dont get. Its the hole in the carboard to sit the spout in. You cut your own hole? Do you pull the ring tab while its sitting in the box or before and put the lid back on? Then just unscrew the lid while its set up. I may be mistaken but IIRC the kits Phil uses have a perforated knock-out section for the nozzle to sit in. The bladders have the nozzle in the center just behind the knockout. I recall discussing it a few months ago and that was the impression I got. The Kegland kit I used does not have a knockout section in the box and the nozzle is located closer to the corner of the bladder. You could try cutting your own hole if you are handy with a pair of scissors. Link to comment Share on other sites More sharing options...
Pale Man Posted November 11, 2023 Share Posted November 11, 2023 2 minutes ago, Kegory said: I may be mistaken but IIRC the kits Phil uses have a perforated knock-out section for the nozzle to sit in. The bladders have the nozzle in the center just behind the knockout. I recall discussing it a few months ago and that was the impression I got. The Kegland kit I used does not have a knockout section in the box and the nozzle is located closer to the corner of the bladder. You could try cutting your own hole if you are handy with a pair of scissors. All In Brewing kits do not have a perforated knock out piece for the spout. Only carry handles. So cutting my own is the only option. All that doesnt get away from the fact its a PITA to pour no matter what you do. They could make it easier by adding in a section for the spout to sit, and an on off tap. 1 Link to comment Share on other sites More sharing options...
Kegory Posted November 11, 2023 Share Posted November 11, 2023 38 minutes ago, Pale Man said: All In Brewing kits do not have a perforated knock out piece for the spout. Only carry handles. So cutting my own is the only option. All that doesnt get away from the fact its a PITA to pour no matter what you do. They could make it easier by adding in a section for the spout to sit, and an on off tap. I agree. Even a fitting where you could unscrew a plug and fit your own tap could be useful. However, I'm not going to hold my breath waiting for that to happen. 1 Link to comment Share on other sites More sharing options...
Cheap Charlie Posted November 11, 2023 Share Posted November 11, 2023 1 hour ago, Pale Man said: All In Brewing kits do not have a perforated knock out piece for the spout. Only carry handles. So cutting my own is the only option. All that doesnt get away from the fact its a PITA to pour no matter what you do. They could make it easier by adding in a section for the spout to sit, and an on off tap. Improvise, adapt and overcome, soldier! 1 1 Link to comment Share on other sites More sharing options...
Classic Brewing Co Posted November 11, 2023 Share Posted November 11, 2023 1 hour ago, Pale Man said: All In Brewing kits do not have a perforated knock out piece for the spout. Only carry handles. So cutting my own is the only option. All that doesnt get away from the fact its a PITA to pour no matter what you do. They could make it easier by adding in a section for the spout to sit, and an on off tap. It is a pity that all the manufacturers like to cost cut as the old plastic HDPE tubs were the best & also useful afterwards, there are a couple that still use them but living in Adelaide means the shipping costs are far too high. 2 Link to comment Share on other sites More sharing options...
Pale Man Posted November 11, 2023 Share Posted November 11, 2023 1 minute ago, Cheap Charlie said: Improvise, adapt and overcome, soldier! Ive got no choice have I. Luckily its a very good product, just not user friendly. 1 Link to comment Share on other sites More sharing options...
Cheap Charlie Posted November 11, 2023 Share Posted November 11, 2023 25 minutes ago, Pale Man said: Ive got no choice have I. Luckily its a very good product, just not user friendly. I've tried them a few times, produces pretty good beer and very convenient, however I have had the same issues as you mate, some all over the kitchen floor, a very messy clean up. I've tried the bag in the box and out of the box. Yep, a PITA. And also, can never get ALL of the wort out. Next time I will try the snip the corner method. You are not alone mate. 2 Link to comment Share on other sites More sharing options...
Classic Brewing Co Posted November 11, 2023 Share Posted November 11, 2023 42 minutes ago, Cheap Charlie said: I've tried them a few times, produces pretty good beer and very convenient, however I have had the same issues as you mate, some all over the kitchen floor, a very messy clean up. I've tried the bag in the box and out of the box. Yep, a PITA. And also, can never get ALL of the wort out. Next time I will try the snip the corner method. You are not alone mate. I have snipped the corner, also added a bit of water & shaken it up - no waste. 2 Link to comment Share on other sites More sharing options...
Back Brewing Posted November 11, 2023 Share Posted November 11, 2023 If I was to put down a can of cooper's draught with a kilo of dry malt extract with 100g of light crystal malt and 100g of carapilis both steeped for 30 mins When I brought the grain liquid to a boil how much Chinook hops would I add to the boil and for how long to get a nice bitter finish without it punching you in the face and be overpowering? I was thinking maybe 15g boiled for 5 minutes 2 Link to comment Share on other sites More sharing options...
Classic Brewing Co Posted November 11, 2023 Share Posted November 11, 2023 20 minutes ago, Back Brewing said: If I was to put down a can of cooper's draught with a kilo of dry malt extract with 100g of light crystal malt and 100g of carapilis both steeped for 30 mins When I brought the grain liquid to a boil how much Chinook hops would I add to the boil and for how long to get a nice bitter finish without it punching you in the face and be overpowering? I was thinking maybe 15g boiled for 5 minutes Personally, I would say 30gm would be better, but it depends on your taste. 1 Link to comment Share on other sites More sharing options...
Kegory Posted November 11, 2023 Share Posted November 11, 2023 52 minutes ago, Back Brewing said: If I was to put down a can of cooper's draught with a kilo of dry malt extract with 100g of light crystal malt and 100g of carapilis both steeped for 30 mins When I brought the grain liquid to a boil how much Chinook hops would I add to the boil and for how long to get a nice bitter finish without it punching you in the face and be overpowering? I was thinking maybe 15g boiled for 5 minutes Have you tried playing around with the Ian H Spreadsheet? You can vary the amounts and boil times and it has a chart that shows you the outcome in terms of bitterness and hoppiness vs maltiness. 1 Link to comment Share on other sites More sharing options...
Back Brewing Posted November 11, 2023 Share Posted November 11, 2023 1 minute ago, Kegory said: Have you tried playing around with the Ian H Spreadsheet? You can vary the amounts and boil times and it has a chart that shows you the outcome in terms of bitterness and hoppiness vs maltiness. Nope 1 Link to comment Share on other sites More sharing options...
Pale Man Posted November 11, 2023 Share Posted November 11, 2023 1 hour ago, Back Brewing said: If I was to put down a can of cooper's draught with a kilo of dry malt extract with 100g of light crystal malt and 100g of carapilis both steeped for 30 mins When I brought the grain liquid to a boil how much Chinook hops would I add to the boil and for how long to get a nice bitter finish without it punching you in the face and be overpowering? I was thinking maybe 15g boiled for 5 minutes I personally wouldn't try to extra bitter Coopers Cans, they have way enough bitterness. I think some over the top. Flame out hops for flavour or dry hopping is very sufficient if you want to add that zing. 2 Link to comment Share on other sites More sharing options...
Classic Brewing Co Posted November 11, 2023 Share Posted November 11, 2023 3 minutes ago, Pale Man said: I looked at that Ol Chop. Basically they've changed the box design and thats it. Whoopdey Doo!!! Yeah, still good beer though. 1 Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now